Skip to main content

Flooring for the main level: Part 1.

Flooring material for the main level was an easy choice.  It was so easy that we installed it in May 2017 before the walls were even erected!  We decided early in the process that the concrete slab was a good use of material.  Since the concrete was already in place it could be used as the primary floor and there was no need wasting more resources on flooring and installation.  Luckily, there are now companies in Newfoundland that grind and polish concrete floors!  One such company, Sam Roberts Cement Finishing, located in St. John's, has been working concrete for 2-3 generations.  Grinding and polishing is a new venture for their long lived company but I have a feeling that it will take off once people see the real potential of a concrete floor.   My feeling from the beginning was that covering a major part of the thermal mass of the building wasn't the best idea.  It really seemed like covering it would be wasting materials.   Besides, at the quoted price, it was cheaper than laying hardwood or other flooring alternatives.  It saves me from the headaches of dealing with wood on concrete and the potential for expansion and buckling.

When I showed up on site the guys were already there and ready to start (Photo 1-2).  The equipment they use is part of the Husqvarna HiperFloor finishing system.   There are several walk behind grinders which have interchangeable grinding heads which vary in grit from very coarse to very fine.  working through grits can give a finish that looks like mirror.  Each grinder has the ability to be connected to what looks like a cyclone dust collector (Photo 1-2).  The result is much less dust than traditional grinders.

In the initial stages it is a matter of determining what type of exposure is desired:  i.e. how far to grind and therefore how much aggregate to expose.  Deeper grinding leads to larger aggregate exposure.  I find this look too busy.  Instead, I opted for something more subtle: a little beyond a salt & pepper finish.  For this space I felt like it made sense.  It took some time to get a feeling for the hardness of the concrete and to strip the initial sealer (sealer was used to prevent the slab from drying to fast during the warm summer months.)

After working through several grits (starting at 20), the slab exposure starts to take shape.   Once the slab is ground smooth,  grits are changed in order to get a smooth finish with a high degree of polish. A densifier is added to the slab and allowed to dry.  After that, the slab is further polished and sealer is used to protect the surface.  The slab is then polished for the final finish.

At this point the guys just have a few minor touch ups.....then we'll have the final reveal!!!



Photo 1-1.  Sam Roberts and his crew on site.  Ready to take on an exciting project!








Comments

  1. David, we are also thinking of polishing our coloured insulated slab. I was planning on doing it all, including polishing, before framing etc. My rationale is it would be easier for the contractor especially in the corners. Thoughts?

    ReplyDelete
    Replies
    1. it would be easier...but it will be pretty much be impossible to keep the floor protected during construction. I would highly recommend against polishing before the framing..I think you will be disappointed. the trades aren't going to be that careful and it is likely that you will have issues. Im glad that I waited. When you see a hammer dropping from the second floor you won't be sorry!

      Delete

Post a Comment

Popular posts from this blog

Building the Air Tight Barrier: Door Flashing Details.

It took us a while to wrap our heads around the door details on my plans.  The main exterior wall is composed of 2x8s.  The rough stud opening was substantially larger than the door.  Because the walls are much deeper than a standard door frame for a 2x6 wall, the interior of the 2x8 opening was studded with double 2x4s.   Outside of these 2x4s, there is 1.5" of foam and another 2x4 on face which brings the door frame opening flush to the exterior 3" of EPS foam.  The brick mould of the door will sit against the exterior of the wall.  The ganged 2x4s which define the opening will allow the door to open a little further than that of a 2x8 wall.    With the door details finalized, I had to flash the opening as per the plan.  I specified the size/shape for aluminum sill pans and CBS Eavestroughing made them for me.  The sill pans have a kind of end dam to prevent water from entering under the under the stud opening should the door ever leak. (Photo 1-1).   After verifying t

Choosing an HRV...My Thoughts....

So, which HRV do you want for your home?  This is a question not often asked by the homeowner.  When the house is built, somebody installed an HRV and that was it.  The home owner is rarely involved in anything other than turning a knob on the HRV wall control if they dare fool with it at all.  An HRV is probably one of the most important appliances in your house;  it expels moisture, eliminates odours, evacuates stale air from bathrooms, provides clean air to keep you healthy and it recovers a lot of heat that would have otherwise been blown out through the vent on the house.  It serves three main functions: 1.  Supplies the home with fresh dry air. 2.  Removes stale air and removes excess moisture. 3.  Recovers heat or heat/moisture For a low energy home we need an HRV that is as efficient as possible.  With the ventilation unit taking care of exchanging most of the air in the building, having an efficient one will pay for itself in the energy saved over it's lifetime.  Zeh

Introducing: The Flatrock Passive House

So...after 8 1/2 years in our home, we have decided to move on.  Well, not right away! We have quite a bit of planning ahead of us.  With the likely onset of a 233% hike in the cost of electricity from Muskrat Falls (when compared to todays rate of $0.0972/kWh) we decided it was time to take energy consumption seriously before its too late to do anything about it.  The land has been acquired, the planning has started!  I am planning on nipping my energy bill in the bud before it becomes a major sinkhole in my pocket book. Upon investigating current building standards, I realized that the Canadian Building Code is below the standards necessary to really make a difference in energy consumption.  There are some standards like R2000 which can make a difference to total energy usage.  A R-2000 home can use up to 50% less heating energy compared to a code built home; if built properly!  A blower door test will reveal the truth about that. Now....Imagine living in a home where you have em