Skip to main content

Air Sealing Plumbing Vents

Attics are cold in the winter and warm in the summer.  Since they are vented through the soffit they are also drafty spaces.    The attic could become an energy sink without lots of insulation and good air sealing details.  We are at a point in construction where we have to start penetrating out though the air barrier and into the attic.  I find this scary but its another reminder that we are progressing nicely.

With our blower door test measuring air tightness of the air barrier at 0.45 ACH50, I cringe every time somebody suggests that we have to drill a hole in it!  This being said, I knew it would be inevitable.  So we move forward with plumbing and wiring details.  Although we placed all the washrooms on one side of the house, it was pretty much impossible to tie everything into one main vent stack.   There service cavity on the ceiling is 2x4 strapping on face so there just isn't enough room to route each vent to a common place and terminate them together before penetrating into the attic.  Instead there are 3 individual ones which are drilled up through the top plates in the exterior service wall.

I knew there would be little distance between the edge of the pipe and the top plate of the exterior 2x8 wall.  I needed to have enough OSB to tape/seal my gasket.   My plumber, (Melvin Way, Perpetual Plumbing Inc) drilled through the top plate of the exterior wall with a hole saw slightly bigger than the pipe diameter.  He kept the pipe as close to the inside edge of the plate as possible so there would be enough OSB in the attic to provide a surface to air seal.  He stubbed up through the attic with a vent that was about 12" high so I could slip the gasket down over the pipe (Picture 1-1)

When I air sealed the ducts for my ERV and the air intake for the wood stove, I used Roflex gaskets obtained from 475 High Performance Building Supply.  They were pre-made and worked well.  Since then a friend of mine told me to make my own gaskets using an EPDM liner made for backyard ponds.  So I gave it a try.  I cut the gasket to about 6"x6".  I centered the gasket over the end of the pipe and used a utility knife to create a star shaped hole in the gasket by cutting successive lines while using the ID of the pipe as a guide (Picture 1-2).  This ensured that when I went to pull the gasket down, it would still be tight around the pipe.  Using my trusty Ryobi battery powered caulk gun I dispensed a good bead of acoustical sealant both around the pipe and at the edge of where the gasket would lay on the ceiling (Picture 1-3).  Not to get sidetracked but I should mention a couple of things here.  First, if you decide to build a passive house, purchase a battery powered caulk gun...unless you want to look like Popeye!  The caulk gun will pay for itself ten times over!   As a recommendation, I prefer to use use Mulco Acoustik (http://www.mulco.ca/sealants/soundproofing) for air sealing.  Its a low VOC formula acoustical sealant.  It is not quite as stringy as other brands and is a little thicker.  I also find that it is much easier to wipe from your hands....but you'll still get dirty....and it will go everywhere....its acoustical sealant!  What more can you expect!

Once the acoustical sealant is applied, I pull the gasket down over the pipe slowly until the gasket rests flush with the surface.  I apply rubbing pressure to the gasket to ensure it is seated in the acoustical sealant and then apply 3M 8067 tape around the edges.  I use a J-roller to apply pressure to the taped surface to ensure adhesion.  I then finish the detail by wrapping 3M tape around the penetration of the gasket and onto the pipe (Picture 1-4).

I think this is a good redundant air sealing system that is simple to implement on the build site and it doesn't require an fancy materials.   First, either the tape or acoustical sealant would have to fail in order for the air seal to be broken at the base of the gasket.  At the pipe penetration through the gasket, the EPDM is stretched and is compressing around the pipe because of the elasticity.  In this case, the three subassemblies would have to fail in order for the air seal to be broken:  the gasket, the acoustical sealant, and the tape.  Given that all subassemblies are going to be covered in 26" of cellulose indefinitely I expect that there will be little exposure to the elements and the details should remain intact for years to come.

As much as I don't like drilling holes in the air barrier, I'm pretty confident that these details will bring my air barrier back to passive house air tightness.


Picture 1-1.  Plumbing vent stubbed up in the attic.


Picture 1-2.  EPDM pond liner gasket, with a star line pattern cut the same diameter as the ID of the pipe.


Picture 1-3.  Use lots of acoustical sealant.  Its cheap!


Picture 1-4.  Final gasket detail.  Taped, sealed....and delivered!

Comments

Post a Comment

Popular posts from this blog

Building the Air Tight Barrier: Door Flashing Details.

It took us a while to wrap our heads around the door details on my plans.  The main exterior wall is composed of 2x8s.  The rough stud opening was substantially larger than the door.  Because the walls are much deeper than a standard door frame for a 2x6 wall, the interior of the 2x8 opening was studded with double 2x4s.   Outside of these 2x4s, there is 1.5" of foam and another 2x4 on face which brings the door frame opening flush to the exterior 3" of EPS foam.  The brick mould of the door will sit against the exterior of the wall.  The ganged 2x4s which define the opening will allow the door to open a little further than that of a 2x8 wall.    With the door details finalized, I had to flash the opening as per the plan.  I specified the size/shape for aluminum sill pans and CBS Eavestroughing made them for me.  The sill pans have a kind of end dam to prevent water from entering under the under the stud opening should the door ever leak. (Photo 1-1).   After verifying t

Choosing an HRV...My Thoughts....

So, which HRV do you want for your home?  This is a question not often asked by the homeowner.  When the house is built, somebody installed an HRV and that was it.  The home owner is rarely involved in anything other than turning a knob on the HRV wall control if they dare fool with it at all.  An HRV is probably one of the most important appliances in your house;  it expels moisture, eliminates odours, evacuates stale air from bathrooms, provides clean air to keep you healthy and it recovers a lot of heat that would have otherwise been blown out through the vent on the house.  It serves three main functions: 1.  Supplies the home with fresh dry air. 2.  Removes stale air and removes excess moisture. 3.  Recovers heat or heat/moisture For a low energy home we need an HRV that is as efficient as possible.  With the ventilation unit taking care of exchanging most of the air in the building, having an efficient one will pay for itself in the energy saved over it's lifetime.  Zeh

Introducing: The Flatrock Passive House

So...after 8 1/2 years in our home, we have decided to move on.  Well, not right away! We have quite a bit of planning ahead of us.  With the likely onset of a 233% hike in the cost of electricity from Muskrat Falls (when compared to todays rate of $0.0972/kWh) we decided it was time to take energy consumption seriously before its too late to do anything about it.  The land has been acquired, the planning has started!  I am planning on nipping my energy bill in the bud before it becomes a major sinkhole in my pocket book. Upon investigating current building standards, I realized that the Canadian Building Code is below the standards necessary to really make a difference in energy consumption.  There are some standards like R2000 which can make a difference to total energy usage.  A R-2000 home can use up to 50% less heating energy compared to a code built home; if built properly!  A blower door test will reveal the truth about that. Now....Imagine living in a home where you have em